1W415-0607 / A / 01.18.08$10.00CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: ANSI Z21.88 • CSA 2.33 FOR VENTED GAS FIREPLACE HEATERS.INSTA
10W415-0607 / A / 01.18.08V290°H3H190°H2H1V1Simple venting confi guration (only one 90° elbow)Example 2:V1 = VT = 6 ft H1 = 3 ft H2 = 5 ft HR =
11W415-0607 / A / 01.18.08See graph to determine the required vertical rise VT for the required horizontal run HTFor vent confi gurations requiring mor
12W415-0607 / A / 01.18.08V1V290°45°90°90°Simple venting confi guration (only two 90° elbows)Example 5:V1 = 4 ftV2 = 1.5 ftVT = V1 + V2 = 4 + 1.5 = 5
13W415-0607 / A / 01.18.08REQUIRED VERTICAL RISE IN FEETVT HORIZONTAL VENT RUN PLUS OFFSET IN FEET HTThe shaded area within the lines represents acce
14W415-0607 / A / 01.18.08VERTICAL THROUGH EXISTING CHIMNEYThis appliance is designed to be attached to a 3" co-linear fl exible vent system runni
15W415-0607 / A / 01.18.08REAR EXIT CONVERSIONFIGURE 194” Gasket7” Cover Plate7” Gasket4” Gasket4” Collar7” Gasket7” CollarOuter Top4” Cover PlateIn o
16W415-0607 / A / 01.18.081. Determine the air terminal location, cut and frame a 9" square opening in the ceiling and the roof to provide the m
17W415-0607 / A / 01.18.08SCREWS & WASHERS 4" COUPLERSELF DRILLING#8x1/2"7" RIGID VENTPIPESEALANTHIGH TEMPERATURE4" FLEXIBLEVE
18W415-0607 / A / 01.18.08RESTRICTING VERTICAL VENTSVertical termination installations exiting either from the rear or the top flue collar of the stov
19W415-0607 / A / 01.18.08FIGURE 30FIGURE 31RESTRICTOR PLATE1. Remove the front and the door from the stove.2. Remove the screws securing the baffl e p
2W415-0607 / A / 01.18.08• Do not burn wood or other materials in this stove.• Adults and especially children should be alerted to the hazards of high
20W415-0607 / A / 01.18.08FIGURE 34MINIMUM MANTEL, SHELF OR CEILING CLEARANCES1”2”471/2”351/2”5”BRICKCOMBUSTIBLE NON-COMBUSTIBLE291/8” MINIMUMPLUS RIS
21W415-0607 / A / 01.18.08BLOWER INSTALLATIONELECTRICAL INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be connected and grounded in accorda
22W415-0607 / A / 01.18.0890°FINISHINGGLASS DOOR INSTALLATION AND REMOVAL1. Lift the top cast piece off of the unit.2. Pull handle forward and rotate
23W415-0607 / A / 01.18.081. Place the rear log as shown, ensuring the holes on the underside are placed onto the 2 pins of the log support.In order t
24W415-0607 / A / 01.18.08FIGURE 46BATTERYHOLDERGAS VALVEPILOTASSEMBLYIGNITIONMODULEPILOTGAS LINEOrange (I) [throughindependentconduit]Yellow (S)[t
25W415-0607 / A / 01.18.081. STOP! READ THE ABOVE SAFETY INFORMATION ON THIS LABEL.2. TURN REMOTE WALL SWITCH TO OFF POSITION.3. TURN OFF ALL ELE
26W415-0607 / A / 01.18.08NOTE: Check and adjust, if necessary, the primary air to 7/16” for propane and 1/4” for natural gas. Replace the screws.7.
27W415-0607 / A / 01.18.08Contact your dealer for questions concerning prices and availability of replacement parts. Normally all parts can be ordered
28W415-0607 / A / 01.18.08ATTENTION-CHAUDCAUTION - HOT274435186746175111322382629313234342834252433413837403921164
29W415-0607 / A / 01.18.08Pilot will not light.Verify the "S" wire for the sensor and the "I" wire for the ignitor are connected t
3W415-0607 / A / 01.18.08NAPOLEON® products are manufactured under the strict Standard of the world recognized ISO 9001 : 2000 Quality Assurance Certi
30W415-0607 / A / 01.18.08Flames are very ag-gressive.- Venting action is too great.Tighten door clampsRestrict vent exit with restrictor plate. See R
31W415-0607 / A / 01.18.08Wolf Steel Fireplace Service HistoryThis fireplace must be serviced annually depending on usage.DateService Technician NameS
32W415-0607 / A / 01.18.08NO TES
4W415-0607 / A / 01.18.08FOR YOUR SATISFACTION, THIS STOVE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND QUALITY! Minimum inlet gas supply pressure
5W415-0607 / A / 01.18.08351/2”37”181/8”235/8”4” DIA.7” DIA.GASLINEACCESSELECTRICALACCESS291/8”DIMENSIONSFIGURE 1aVENTINGVENTING LENGTHS AND AIR TERMI
6W415-0607 / A / 01.18.0816”MINIMUM40 FT MAXIMUM3 FT MINIMUM16”MINIMUM40 FT MAXIMUM3 FT MINIMUM TYPICAL VENT INSTALLATIONSFIGURE 2aFIGURE 3a* Refer to
7W415-0607 / A / 01.18.08FIGURE 6MINIMUM AIR TERMINAL LOCATION CLEARANCES
8W415-0607 / A / 01.18.08VENTING APPLICATION FLOW CHARTSTOVE VENT EXITREAR EXITTOP EXITHorizontal TerminationVertical TerminationVertical TerminationV
9W415-0607 / A / 01.18.0890°90°90°H1V2H2V1Simple venting confi guration (only one 90° elbow) For vent confi gurations requiring more than one 90° elbow,
Kommentare zu diesen Handbüchern